Zenwalk 4.6.1 on 450Mhz K6-2, 256Mb

Edit: Unfortunately, the images originally included in this post are gone, because of hosting problems in late 2009. My apologies.

Ordinarily Zenwalk is mentioned in the same breath as distros like Xubuntu or Slax, as a full-featured alternative to something like Ubuntu, that generally has a quicker feel to it. I have suggested it to many people myself and for those same reasons, but this time my own advice turned out to be a disappointment.

The Ugly Little Laptop — which I am starting to feel sorry for — had an awful time running Zenwalk. It wasn’t as bad as a full Ubuntu installation, but even Xubuntu seemed to have more pep than Zen.

Installation was easy as pie, although it’s been a while since I worked with a system that had to reboot to finish configuration. I think the last time I saw that was Breezy. It set itself up perfectly though, with no hassles or difficulties.

The only quirk was the network card again, which this time was recognized, and the xircom_cb module was inserted, but it wasn’t activated when I logged in. And I think I committed the error of leaving myself out of a network group, because I wasn’t allowed to access ifconfig, even with sudo.

Which made for an additional complication: I could only bring up the network by logging in as root in a terminal window, but for some reason, I couldn’t bounce back to the GUI. CTRL+ALT+F7 left me at a blinking cursor.

So I would restart gdm from the root console, which suddenly made the entire machine run dog slow. I don’t know how or why that was happening, but it was taking all the longer for things to get around to a workable state.

Like I said, that whole unfortunate sequence is probably my fault, and could probably be fixed with a simple one-line command. But it would only make things a little easier, since performance was terrible to start with.

Boot times from LILO to the desktop were around two minutes, and that was without a network. Firefox took its grand old time, finally popping up in 19 seconds, but without network access. xfce4-terminal, with nifty transparency effects by default, opened in just under 5 seconds, and Thunar needed about the same. Shutdown was around 39 seconds, from clicking “Quit” to a full poweroff.

So altogether, the entire experience on this machine was about par with Xubuntu — sometimes faster, sometimes slower.

Zenwalk does a few things differently, that I like. First, I think the mountpoints icon on the desktop is a very good idea. Rather than spattering icons all over the place to represent every partition on the drive, you get one persistent icon, and opening it gives you all those drives/partitions in a nice neat bundle. Very clean and very efficient.

Also, I find the Zenwalk XFCE to be closer to the old-style XFCE layout, which I prefer to Xubuntu’s phony Gnomeified one. I know, those things can be changed, but … well, never mind.

In short, Zen didn’t do the trick for me. It might be that this machine is too old for it, or that there’s some sort of hardware muck that keeps it from running at the speed its reputation gives it. It might also be that it has suffered the same fate of Xubuntu — that as it grew and became more popular, it snowballed into something more hefty than originally advertised.

I can’t answer that, mostly because I’m just a passing observer, looking for a distro that works well without pinching in the wrong places. Kind of like shoe shopping, isn’t it?

About these ads

5 Responses to “Zenwalk 4.6.1 on 450Mhz K6-2, 256Mb”


  1. 1 David 2007/09/09 at 11:07 AM

    Why not try Elive or Vector, in addition to the ones you already have? Or, if you really think that you’ll just end up back at Ubuntu then why not just stop wasting your time and reinstall it then give your poor laptop a rest.

  2. 2 PaLO 2007/09/09 at 4:48 PM

    Another vote for vector linux 5.8. I am using their standard edition on celeron 450mhz and slighty more ram and it feel snapy enough for me. Keep in mind that key is tuning distro for old pc not just picking the right one. On my other notebook HP nc 6000 i was using vector 5.8 soho handy tuned to boot to 36mb ram used. (yep with KDE).Just google for “optimize linux for old pc ” .

    If it doesnt work for ya there’s stil DSL , puppy and bsd family.

    Good luck

    PaLO

  3. 3 Zlatan Kadragić 2007/09/09 at 6:16 PM

    Try Wolwix: http://wolvix.org/ , small but very nice distro
    or DeLi linux: http://www.delilinux.org/ , for 486 or better procesors

  4. 4 K.Mandla 2007/09/09 at 7:59 PM

    Two votes for Vector Linux cannot be ignored. I shall try it! :)


  1. 1 Vector Linux 5.8 on 450Mhz K6-2, 256Mb « Motho ke motho ka botho Trackback on 2007/09/10 at 9:27 AM

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s




Welcome!



Visit the Wiki!

Some recent desktops


May 6, 2011
Musca 0.9.24 on Crux Linux
150Mhz Pentium 96Mb 8Gb CF
 


May 14, 2011
IceWM 1.2.37 and Arch Linux
L2300 core duo 3Gb 320Gb

Some recent games


Apr. 21, 2011
Oolite on Xubuntu 11.04
L2300 core duo 3Gb 320Gb

Enter your email address to subscribe to this blog and receive notifications of new posts.

Join 405 other followers

License

This work is licensed under the GNU Free Documentation License. Please see the About page for details.

Blog Stats

  • 3,963,830 hits

Archives


Follow

Get every new post delivered to your Inbox.

Join 405 other followers

%d bloggers like this: